输出功率

对两种工艺下工艺参数对显微硬度的影响进行了研究，最终确定出优化后的表面处理工艺参数为：高频淬火装置输出功率为26.1kW；

We studied the effect of processing parameter of the two surface treatment techniques on microhardness . Finally , we obtained optimal surface treatment processing parameter : high-frequency induction quenching output power 26.1kW ;

自持电激励横流CO2激光器的最佳输出功率

Optimum output power of a self-sustained discharge transverse flow CO_2 laser

流速对高气压电激励CO2激光器输出功率的影响

Influence of flow velocity on output power of high pressure CW CO_2 lasers

电子束蒸发器的性能试验表明，稳定输出功率可以控制输出稳定的Si束流。

Steady Si beam can easily be obtained at a constant power output .

在激光谐振腔内放置一x向位置可根据激光输出功率的变化而移动的补偿透镜，从而在大功率激光输出时消除腔内的热透镜效应，形成一热稳定腔。

Place a locomotive compensated lens in the cavity , its motion according to the change of output laser power .

输出功率与NaCl浓度有关。

The output power increases as NaCl concentration increases .

提高稳频He－Ne激光器输出功率的研究

Enhancement of Frequency Stabilized He Ne Laser Output Power

合理的设计对提高Cr，Tm，Ho∶YAG激光器的输出功率是很重要的。

Reasonable design plays an important role to increase Cr , Tm , Ho ∶ YAG laser power .

LD抽运Nd∶YVO4平行平面腔激光器中的激光输出功率凹陷

Dips of Output Power Curve of LD Pumped Nd ∶ YVO_4 Plane-parallel Cavity Laser

在同样的直流输入电压情况下，这种新型结构的输出功率是传统单端E类放大器的4倍，极大地提高了输出功率。

The output power of this new structure is four times of that of conventional single end class E amplifier at the same DC input voltage .

它的性能决定着PEMFC的输出功率、电池效率、成本及应用前景。

Its performance significantly affects the PEMFC ′ s power density , efficiency , cost and application , etc.

通过数值计算分析可知，对于F-P腔结构的双包层光纤激光器，采用后向泵浦比采用前向泵浦获得的输出功率大，增益分布也较后者平坦；

Considering F-P cavity , backward pumping generates more output power and more even gain distribution than forward pumping .

结果表明，阈值电流在可以接受的范围内略有增加，但半导体激光器抗损伤阈值（COD）、斜率效率和输出功率得到明显提升。

The results show that , threshold current increased slightly within the acceptable limits , but the damage threshold of semi-conductor laser , slope efficiency and output power improved obviously .

该电源采用全桥逆变拓朴电路、PWM控制方式、输出功率叠加的方案，具有输出变压器原边平均电流和副边峰值电流的过流保护功能。

Full bridge inversion topological circuit , PWM control method and output power superposition are adopted , over-current protection of the output transformer original side average current and side peak current included .

研究了焦点位置、输出功率和不同气体切割环境对金刚石膜切割的影响，给出了采用NdYAG激光器切割金刚石膜的具体方法。

The influences of focus position , output power and different gas to diamond film cutting are studied . The cutting technology of diamond film with Nd : YAG laser is discussed .

这些都是围绕调制器的性能参数来研究的，它们包括：半波电压，单模特性，偏振特性（TE和TM模之间的输出功率比值），损耗，带宽及分支比等。

The analysis concentrates on those performance parameters of a modulator : half-wave voltage , single mode performance , quasi TE / TM polarization , loss , bandwidth and split-ratio .

然后用浓度为2mg/mL的CoFe2O4纳米悬浮液在不同输出功率的交变磁场下测定温度随时间的改变。

At the same time , measured 2 mg / mL CoFe_2O_4 nanoparticles suspension concentration temperature and time in differ alternating magnetic field .

设计输出功率500W。

The output power is 500W .

D2流率过高所造成的激光器输出功率下降是由于D2增加了激发态DF分子的去激活，以及大量增加D2流率会造成了气体动力的扰动。

The D2 increases the activation energy of DF and gives a disturbance to the gas-drive , so the output power decreases as the D2 's flowing voltage increases .

动态运转时，平均输出功率达到4W，相应的能量抽取效率大于85%。

The average output power of 4 W are obtained corresponding to 85 % extraction efficiency in dynamic running .

通过腔外光反馈调制He－Ne激光器的放电电流，使激光器的输出功率稳定度达到了0.1%。

This technique of light feedback outside the cavity to modulate the discharged current of He Ne laser is developed to stabilize the power output of the He-Ne laser to reach 0.1 % .

通过热沉积系数研究在激光提取条件下掺杂原子分数为1.0%的NdYAG陶瓷激光器中热沉积问题.热沉积系数定义为热沉积功率与激光器输出功率之比。

The heat generation in Nd : YAG ceramic lasers under the conditions of laser extraction was investigated through the heat generation coefficient , which was defined as the ratio of heat generation power to laser output power .

在毫米波系统日益追求小型化、轻量化的今天，毫米波VCO的体积、重量面临新的要求，同时又需要保证较大的输出功率、较宽的调谐频带、良好的相位噪声以及利于系统集成。

Today , millimeter-wave systems are expected to be more and more compact and light , so reduction of both dimensions and weight of the circuits is needed .

在泵浦功率为17.1W，脉冲重复率为20kHz时，得到5.84w的调Q输出功率。

When the incident pump power is 17.1 W and the pulse repetition is 20 kHz , an average output power of 5.84 W is obtained . 3 .

使用激光二极管（LD）泵浦的固体激光器，与传统的激光器相比可以实现高输出功率、高重复频率，窄脉宽的激光输出。

Compared with other lasers , the output of the laser-diode ( LD ) pumped solid-state laser is special in the high peak power , the high pulse repetition rate and the narrow pulse width .

通过应用单层增透膜MgF2，太阳电池的输出功率提高2%；

The output power of space solar cells is increased 2 % by using single-layer AR coatings ;

基于SR电机的准线性模型，本文分析了开通角和关断角与相电流、输出功率以及损耗之间的关系，并根据给定的优化目标，给出了该电机开通角和关断角的优化结果。

Based on quasi-linear model of SR motor , the influences of angle on phase current , output power , energy loss are analyzed . An optimum result of angle is produced in accordance to given target .

方法①对黏膜黑斑采用CO2激光治疗，治疗输出功率15～20W，分3～4次治疗完毕；

Methods ① Using the laser of CO 2 to treat the black spots of mucosa for 3 ~ 4 times . The power of laser is between 15 ~ 20 W.

目前，BMFC还没有得到广泛应用，关键问题是输出功率密度较低。

The key issue is the low output power density .

结果表明，柴油机采用EGR后，由于废气的引入，使柴油机的平均有效压力、输出功率和有效热效率随着EGR率的增加而降低。

The results showed that when EGR ratio was increased , an associated consequence of it was the reduction in the mean effective pressure , power output and thermal efficiency of the engine .