缩水率
- 名shrinkage
-
美国AATCC指定的标准缩水率测试机。
American AATCC assigns standard shrinkage test machine .
-
降低兔毛针织物缩水率的新工艺研究
New process of reducing the washing shrinkage of rabbit hair knitted fabrics
-
通过对树脂、催化剂、添加剂等助剂以及工艺条件的研究,摸索出一套纯棉高支织物PP整理的加工方法,使之加工的衬衫缩水率<0.5%,回弹性。
The influence of resin , catalyst , additives as well as process conditions were researched on permanent press ( PP ) finishing of high counts pure cotton fabric .
-
测试了DTY长丝的物理机械性能、抗菌性能和耐气候牢度,以及其经编针织物染色成品的缩水率、变色和抗菌性能。
The physical-mechanical property , anti-bacterial property and color fastness to weathering of DTY filament , as well as water shrinkage , color change and anti-bacterial property of its dyed products were tested .
-
纯棉纬平针织物缩水率控制方法
The Water Shrinkage Control of Weft Plain Fabric from Pure Cotton
-
着眼光坯面料降低针织成品缩水率
Improving the shrinkage of Knitted End Products Starting with Greige Fabrics
-
买棉衣时最好要考虑到它们的缩水率。
It is better to allow for shrinkage when buying cotton clothes .
-
全自动织物缩水率试验机的研制
The Development of An Automatic Testing Machine of Shrinkage Rate
-
我们缩水率可以做到你要求的。
We can control the shrinkage according to your request .
-
针织毛衫不同组织缩水率的研究
A study on sweater shrinkage knitted with different stitch
-
影响前列腺电切组织缩水率的因素探讨
Factors affecting shrinkage of the prostate during transurethral resection
-
采用先进设备和工艺降低缩水率
Adopting Advanced Equipment and Technology for Improving Shrinkage
-
控制纯棉针织棉毛布缩水率的机械整理方法
Physical-Finishing Method of Pure Cotton Interlock Shrinkage Control
-
丝光烧毛棉针织物缩水率的控制
Shrinkage Control of Mercerized and Singed Cotton Knits
-
影响棉/氨纶交织汗布缩水率因素的探讨
Study on the Factors of Influencing the Shrinkage of Cotton / Polyurethene Interwoven Knitting Fabrics
-
弹力织物幅宽与缩水率的控制
Width and shrinkage control of elastic fabric
-
真丝绸缩水率及尺寸稳定性
Shrinkage and Dimensional Stability of Real Silks
-
织物缩水率指标测试的研究
Researches on Fabric Shrinkage Indices Testing
-
前处理后不能有纬斜,缩水率小于5%。
After preparation , no skewing is found and water shrinkage is less than 5 % ;
-
衬布生产过程中的缩水率控制技术
Interlining Shrinkage Control in Production
-
用于棉纺、印染、服装等行业进行缩水率试验的烘干设备。
It is a stoving equipment of shrinkage test in cotton textile , dyeing and clothes trade .
-
这个最后的整理步骤再一次降低剩余缩水率并且改善了手感,增加了织物体积。
This last finishing step reduces once more the residual shrinkage potential and improves handle and volume of the fabric .
-
针对不同织物组织编织的毛衫,经洗涤后的保形问题,用实验方法研究了相同原料、相同纵向密度、不同织物组织的针织毛衫的缩水率情况。
Shrinkage of sweater after washing knitted with same material , same density and different stitch was studied by means of experiment .
-
分析绳状连续式生产设备对针织产品的缩水率和其它质量问题的影响因素。
Based on practical application , it is found that continuous rope bleaching machine exerts serious influence on the shrinkage and other quality problems of the knitted goods .
-
在双针床经编机上,以纯棉纱为原料,经过对织物结构的分析、设备性能的研究、织物缩水率的探讨、试制成纯棉保暖织物。
The thermal fabric has been produced with cotton yarn on double warp knitting machine through the study on fabric structure , equipment performance and the washing shrinkage of the fabric .
-
通过试验还初步探讨了洗涤溶液、洗涤温度、经纬密度及织缩对总缩水率的影响。
Also the influences of the detergent species , the washing temperature , the warp-wise and weft-wise thread counts and the weaving shrinkage on the total shrinkage of the fabrics are discussed .
-
并测试了纤维素酶处理粗棉布前后断裂强度、硬挺度、悬垂系数、弹性、缩水率、丰满度的变化。
The change of breaking strength , stiffness , drape coefficient , elasticity , water shrinkage , fullness of coarse count cotton fabric in the course of treating by cellulose were tested .
-
纬编针织物通过丝光整理,有效地提高了产品的光泽、降低了缩水率、提高了上染率,并提高了产品的档次,增加了经济效益。
Mercerizing process on weft knitted fabric can offer a higher grade product with an improved luster , lower shrinkage and a higher dye uptake in addition to an increased economic benefit .
-
采用不同类型防缩抗皱整理剂、不同工艺进行复合整理,12102双绉干弹回复角达到300°,湿弹回复角达到265°以上,缩水率降至3%以下。
It is found that the finished Crepe de Chine 12102 reaches 300 degrees in dry crease recovery , over 265 degrees in wet crease recovery , and below 3 % in shrinkage .
-
按你们提供的缩水率千分之五,这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确?
Acording to the shrinkage one over two hundred , the mold has been done in the right dimension , but the part falls short to your part drawing , are you sure the shrinkage is right ?