砂轮磨削

树脂结合剂CBN砂轮磨削力的试验研究

An Investigation on the Grinding Force with the Resin-Bonded CBN Wheel

金刚石砂轮磨削Al2O3-Mo金属陶瓷的试验研究

Experimental Research on the Grinding of Al 2O 3-Mo Ceramet with Diamond Wheel

用CBN砂轮磨削轴承套的工艺实践

Technological Practice on Bearing Sleeve Grinding Using CBN Grinding Wheel

陶瓷结合剂CBN砂轮磨削表面粗糙度的试验研究

Experimental Research on Surface Roughness in Grinding with Vitreous Bond CBN Wheels

磨削液对陶瓷结合剂CBN砂轮磨削性能影响

Effect of Grinding Fluid on Grinding Performances of Vitrified Bonded CBN Wheel

用CBN砂轮磨削氧化锆-钢合成部件

Study on Grinding Zirconium Oxide-Steel Components with the CBN & Grind wheel

陶瓷结合剂CBN砂轮磨削钛合金的研究

A Study on the Grinding of Titanium Alloys with Vitrified CBN wheel

电镀CBN砂轮磨削内孔的表面粗糙度

Surface Roughness of Internal Grinding with Electroplated CBN Wheels

电镀CBN砂轮磨削内孔的一些研究

Study on Internal Grinding with Electroplated CBN wheel

人造金刚石树脂砂轮磨削比的提高方法金刚石砂轮恒力磨削Si3N4陶瓷的钝化模型

On Grinding Rate of Man-made Diamond Resin-bonded Grinding Wheel ; Passivation Model of Diamond Wheel for Constant-force Grinding Si_3N_4 Ceramics

磨粒裸露高度对树脂结合剂CBN砂轮磨削性能影响的研究

Effect of Exposed Height of Grain on the Grinding Performance of Resinoid Bonded CBN Wheel

机床特性对陶瓷结合剂CBN砂轮磨削比的影响

Analysis of the influence of the characteristic of machine tool on the grinding ratio of CBN wheel

讨论了Al2O3砂轮磨削耐热合金时磨削比低、表面质量差的原因。

The causes resulting in a bad surface integrity and low grinding ratio during grinding superalloys by using Al2O3 wheels have been discussed .

介绍了超硬磨料立方氮化硼（CBN）砂轮磨削性能的优越性。

Superiority of grinding property of the extra-hard abrasive cubic borium nitride ( CBN ) grinding wheel is presented .

为了减小钟形壳椭圆沟道磨削的理论误差，本文提出用CBN盆状砂轮磨削椭圆沟道的一种新方法，并建立了盆状砂轮的数学模型。

In order to decrease the error , a novel grinding method with basin-like grinding wheel is proposed in this dissertation .

试验结果验证了基于TCA分析的面齿轮副性能预控理论和蝶形砂轮磨削理论的正确性及工程可行性。

The experimental results show that the performance pre-control theory based on TCA and grinding disk theory of the face gear are correct .

通过用金刚石砂轮磨削聚晶金刚石（PCD）材料的试验，研究了磨削速度vs对PCD材料磨除率Q、磨耗比G的影响。

Through an experiment of grinding polycrystalline diamond ( PCD ) by diamond grinding wheel , the influences of grinding speed v s on PCD material removal rate Q and grinding consumption ratio G are researched .

本文在小直径CBN砂轮磨削沟槽双侧面、单侧面和底面实验的基础上分析了磨削力对小直径CBN砂轮挠曲变形及其加工精度的影响。

Based on investigation of grinding forces , this paper analyzed the deflection of CBN quill in grove grinding process due to grinding force , and the influence on grinding precision .

根据流体动压润滑理论，分析了平面砂轮磨削时磨削液的流体动压效应，并考虑砂轮渗透度的影响，推得了有限定线接触条件下磨削液三维流动的Reynolds方程。

Grinding fluid flow under a surface grinding wheel is analyzed using hydrodynamic lubrication theory . Considering the effects of permeability of the grinding wheel , a three dimensional Reynolds equation of finite line contact is yielded .

目前，常见的工程陶瓷加工方法有金刚石砂轮磨削、PCD等超硬刀具切削、超声波加工、激光加工、等离子弧切割及高压水射流切割。

At present , the machining method of advanced ceramics have diamond grinding , ultra hard cutters such as PCD , ultrasonic cutting , laser cutting , plasma arc cutting and water-jet cutting .

CBN砂轮磨削时的力、温度值均较SiC砂轮磨削时要低，砂轮磨损速度远远低于SiC砂轮，磨削表面纹理也优于SiC砂轮。

Both grinding force and temperature with CBN wheel are lower than those with SiC wheel . The wearing of CBN wheel is also far slower than that of SiC one . And the appearance of ground surface with CBN is better than that with SiC .

探讨了这些规律产生的机理，得出：CBN砂轮磨削时，磨削力随工件速度增加而略有降低，随切入速度增加而增加，金属切除率和表面粗糙度随切入速度增加而增加。

It is revealed that the grinding force will be slightly reduced with the increase in the workpiece speed and be raised with the increase in grind-in speed , and the metal removal rate and surface roughness will increase with grind-in speed .

盆状砂轮磨削钟形壳椭圆沟道的研究

Research on Outer Race Elliptical Groove Grinding with Basin-like Grinding Wheel

用树脂砂轮磨削低噪音钢球的工艺试验

Process test for grinding low-noise steel ball with resin wheel

硬金属可以很容易用砂轮磨削。

Hard metals can be easily cut with grinding wheels .

精细陶瓷材料的金刚石砂轮磨削性能

Grindability of Fine Ceramics Material With Diamond Grinding Wheel

钎焊金刚石砂轮磨削大理石的力的变化特征

Change characteristics of grinding forces during marble grinding with brazed diamond grinding wheel

圆环面砂轮磨削复杂形状刀具前刀面的分析研究

Research on Rake Grinding Process for Complex Shaped Cutters With Torus Shaped Grinding Wheel

磨料加工的最新进展单层超硬磨料蜗杆形砂轮磨削硬齿面

A Technology of Grinding Hard Gear with Monolayer Super Hard Abrasive Worm Grinding Wheel

金刚石砂轮磨削铁氧体的表面粗糙度与形貌分析

Analysis on surface roughness and surface topography of ferrite ground with diamond grinding wheel