工作点

一种以激光空间定位显示放射线工作点标准量具。

The utility model provides a standard measure displaying the radiation action spot through laser space positioning , relating to a positioning standard measure .

它是一种放射线的空间定位标准量具，使用方便，快捷，准确，并且可以对放射源的工作点和激光定位指示其进行校正。

The utility model is convenient , quick and precise to use and can indicate the correction of the action spot of the radioactive source and the laser positioning .

当出水口压力h确定后，对于确定的定速泵系统其工作点就已经确定了。

When the pressure ( h ) is determinate , so is the working point .

伪工作点与超宽带CMOSLCVCO设计

Pseudo Operation Point and Design of Ultra Broadband CMOS LC VCO

MOSFET放大电路静态工作点的分析及参数选择

Analysis of the quiescent operating point and selection of the parameters in the MOSFET amplifier circuits

对于光纤AMCATV外调制传输，调制器的偏置工作点设置是非常重要的。

The Modulator ′ s bias point setting is very important for optical fiber AM CATV externally modulated transmission .

本文提出一种非线性系统选择工作点的理论方法，并给出了相应的增益调度PID控制器设计方法。

A novel method of selecting reasonable operating points and local models for nonlinear systems will be presented in this paper , also a gain-scheduled PID controller design method developed accordingly .

处于永磁铁磁极之间的磁工质其内部的磁场强度H由磁铁工作点，工质形状，以及工质温度等多种因素决定。

The magnetic field intensity of a magnetic working substance located in the gap of permanent magnet is determined by working point of the magnet , the shape and temperature of the working substance .

通过对流体力学中沿程阻力系数和泵与风机工作点等问题的求解，介绍了EXCEL单变量求解器和曲线拟合的方法。

Through calculating friction factor and operating point of pump or fun of two examples on fluid mechanics , methods using solver and curve-fitting in EXCEL were introduced .

合理的设置偏置电路，使Doherty功率放大器具有合适的静态工作点。

Set reasonable Doherty power amplifier bias circuit to ensure a suitable quiescent point .

从统计结果中总结了DBD介质阻挡放电的电气特性，并从特性出发确定了该负载的最佳工作点。

According to simulation result , electrical characteristic of DBD load has been induced and optimized working point has been determined .

从理论上简要分析了安钢新建100t交流电炉的电气运行工作点的选择。

Selection of the electrical operating points of newly built 100t AC electric arc furnace at Anyang Iron & Steel Co.

并以LCR串联谐振电路为例，分析了系统软开关工作点的周期不动点函数曲线与系统参数间的内在联系。

Afterwards , the relationship between the periodic fixed point function and the system parameters has been studied in a LCR series tuned resonant circuit . 2 .

在此基础上，提出变参数PID控制、负载预测以及发动机怠速切换相结合的方法来稳定单个工作点上的转速平稳，并通过遗传算法进一步提高整机的节能效果，获得了20%左右的燃油节省。

On this basis , variable parameter PID control , load forecasting , and the engine idling switch methods were proposed to stabilize the single speed point steady . By genetic algorithm to further improve the overall energy savings , a20 % fuel savings was gained . 5 .

通过较准确地计算电路的直流工作点和MOS管的小信号参数，以及由电路拓扑结构自动生成电路性能公式对已有的基于公式的方法进行了改进；

In the system , the operating point of the circuit and the small signal parameters of MOS transistor are calculated more accurately , and the circuit performance equations are generated from its topology automatically in order to improve the equation-based method .

新的二重对称高亮度模式lattice（L2）将发射度降低到55.94nm-rad，工作点为（4.45，2.43），直线节处的垂直方向β函数分别为0.35m和3.56m。

The new two-folded high brilliance lattice ( L2 ) decreases the emittance to 55.94 nm-rad . The tunes are ( 4.45 , 2.43 ) . The vertical beta functions in straight sections are 0.35 m and 3.56 m.

针对LAPS检测，设计了自动检测I-V曲线工作点的算法，通过多次样条插值与平滑积分滤波相结合的方法，确定I-V曲线的工作点，并计算出离子浓度变化。

The algorithms for automatic detection of operating points on I-V curves which detected by LAPS were laid out and the cubic spline interpolation with smoothing integral filter were used to determine the operating points of the I-V curve and calculate the ion concentration .

针对330MW单元机组的仿真模型，绘出了其相对非线性测度曲线，并据此得出了单元机组在多个典型工作点的线性化模型；

Firstly , a relative non-linear measure curve of a330MW unit plant is drawn , and then five linearized models of the simulation model are obtained based on this curve .

通过对并联混合动力电动汽车（PHEV）的仿真和对发动机工作点在发动机效率map图中分布情况的分析，研究了影响PHEV的发动机在高效区工作的因素。

Through the simulation of parallel hybrid electric vehicle and the analysis on efficiency map of its engine , the factors making engine works within efficient operation region are studied . This result shows that the most significant affecting factor is the powertrain energy control strategy .

铁心剩磁的存在使电流互感器在B-H曲线上的起始工作点发生变化，加重了饱和程度和缩短进入饱和时间，这是差动保护误动的重要原因。

The residual magnetic flux intensity makes the starting work point of current transformer change on B-H curve , and hence the magnetic saturation state is aggravated in shorter time , which is the main reason to cause the misoperation accident of differential protection .

针对FUDS驾驶循环，计算得到了最少油耗的实时扭矩分配方案，结果表明，该实时控制策略能有效的降低车辆的燃油消耗，优化发动机的工作点。

The torque split scheme for the FUDS drive cycle with minimal equivalent fuel consumption is obtained and the results indicate that the optimal real-time control strategy could improve the fuel economy and optimize the operation points of engine .

同步电机试验特殊工作点的分析

Analysis of Testing of Synchronous Electric Machine for Special Working Points

压水堆核动力装置&回路主泵工作点的确定

Determination of Main Pump Working Point for PWR Nuclear Power Plant

采用网络理论研究了元件的最佳工作点；

Its best working point is analyzed by network theory .

干涉型光纤传感器控制工作点的新方案研究

New method in controlling working point of an interferometric fiber optic sensor

永久磁铁工作点的优化计算

Calculating of the Best Working Point of the Permanent Magnet

水泵并联运行工作点确定方法的研究

Study on methods to determined the operating point of pumps in parallel

磁铁工作点的确定与磁路计算

Determination of the operating point of a magnet and magnetic circuit calculation

通过在线自寻优，使系统很快地趋向于最优工作点。

The system can quickly achieve the optimization point via self-optimization online .

氦制冷机节流级的最佳工作点

The optimum working state of J-T stage of helium refrigerator