变形力

  • 网络deformational force;deformation force;strain force
变形力变形力
  1. 三层复合板轧制复合变形力的计算

    Calculation of rolling deformation force of three-ply cladding sheet

  2. 改善模具的润滑条件,可大幅度地降低变形力。

    The improvement of lubrication condition of die can considerably decrease the deformation force .

  3. 根据变形力的强度,褶皱可以是平缓的,陡峭的,倒转的,或逆掩的。

    Depending on the intensity of the deforming forces the folds may be gentle , sharp , overturned , or overthrust .

  4. 热挤压变形力的粘塑性模式解

    Solution of deformation force in hot extrusion with viscoplasticity model

  5. 锥形件柔性旋压成形时的变形力分析

    Analysis of the Spinning Forces on Flexible Spinning of Cones

  6. 用工程法求解可膨胀管塑性变形力

    Calculating plastic deformation force of expandable tubules by engineering method

  7. 电机换向器整体冷锻变形力的计算

    Forming pressure calculating of integral motor commutator cold forging

  8. 挤压工艺轴对称状态与平面应变状态变形力之间的关系

    Deforming Force Relationship Between Axisymmetric State and Plane Strain State in Extrusion Technology

  9. 等径弯曲通道变形力的研究

    Calculation of extrusion force in equal channel angular pressing

  10. 利用塑性介质挤胀成形三通管接头变形力的研究

    Research on the Deformation Force of Extrude-bulge Forming of Tee Junction Using Plastic Medium

  11. 开式模锻型腔充满阶段和锻靠阶段的变形力

    The deformation force in cavity of closed-die in stages of filling and die kissing

  12. 超塑性材料的镦粗变形力的研究

    Upsetting forming pressure study of superplastic materials

  13. 用能量法研究超塑性矩形条料镦粗的变形力

    Calculation of deformation force for superplastic rectangular blank ( plane strain ) upset by energy equilibrium

  14. 实体可膨胀管变形力与膨胀工具模角关系研究

    On the relationship between the deformation force of solid expandable tubular and model angle of expandable tool

  15. 变形力沿宽度方向的分布都是关于b/h函数。

    Distortion force distributing along the direction of breadth is a kind of function about b / h.

  16. 采用矩阵算子法计算已知滑移线场理论变形力

    Calculation of the Theoretical Working Pressure of a Given Slip Line Field by Using the Matrix Operator Method

  17. 应变速率、液体体积分数和液体粘度对金属半固态成形变形力的影响

    Effects of strain rate , liquid volume fraction and liquid viscosity on deformation force of semi-solid compression of metals

  18. 本文应用逐次单元法推导了开式冲孔变形力计算公式。

    In this paper the deformation load formula of open die punching were derives by the successive element method .

  19. 冷挤压制造圆柱体形孔内侧表面的矩形螺旋单元时的变形力计算

    Calculation of the deformation force during manufacture by cold extrusion of square screw elements on the internal surface of cylindrical cavity

  20. 分析影响旋压工艺变形力的主要因素,介绍了确定旋压工艺力的基本方法。

    Through analysing the main factor that affects spinning technology deform force , this passage introduces the basic method of spinning technology force .

  21. 弹性可被定义为当施加于材料上的变形力被撤除时,材料恢复其原来形状的能力。

    Elasticity can be defined as the ability of the material to return to its original shape when the deforming force is removed .

  22. 应用古典振动理论及冲击波动理论,对三种弹性元件悬架车辆的振动进行模拟并对响应进行分析。提出用冲击波动力学分析车辆振动的理论依据,由此建立车辆的波阻力及变形力振动模型。

    The classical vibration theory and impact wave theory are applied to simulate the helical spring suspension vehicle vibration and its response is analyzed .

  23. 根据破裂模型和拉深变形力,导出了破裂极限预报与控制判据。

    On the basis of the fracture model and the deep drawing deformation force . The fracture limit prediction and control criterion is calculated .

  24. 从谐波齿轮传动的原理和特点出发,分析短筒谐波齿轮传动中短筒柔轮的变形力和应力急剧增加的问题。

    Based on the principle and characteristic of harmonic gear driving , researched the problem about the sharp increase of stress in short flexspline deformation .

  25. 阐述用机械压力机进行粉末热锻时Fe-0.22C粉末烧结体热复压变形力的工程计算。

    This paper expounded the engineering calculation of deformation force for the hot repressing of the Fe 0.22C powder sintered preforms in the hot powder forging by mechanical press .

  26. 对影响16MnCrs钢温锻成形工艺的主要因素锻造温度、表面氧化、摩擦、润滑和变形力进行了研究,并给出了大量的实验数据。

    Some research work have been done in the key influence factors on warm precision forging process , i. e. , temperature , oxidation , friction , lubrication and deformation forces .

  27. 上限模拟通过所设计的简便精确的动可容速度场,获得了变形力和轴对称变形区的变化规律。

    Through an easy to use and accurate enough kinematically permissible velocity field designed with UBM , the magnitude of deformation force and the regularities of axisymmetrical deformation zone are obtained .

  28. 基于滑移线场的简化流动模型,运用数学方法求解出了一种锥形模正挤压变形力的最佳上限解,并将该上限解用通用解析式表达出来。

    The deforming force of cone-die direct extrusion is solved by a mathematic method based on the simplified flow model of slip line field . The optimum upper bound solution is also represented in analytic mode .

  29. 温挤压作为一种少无切削成形技术,因其成形精度高、变形力小,且可连续生产的特点,已被逐渐用于各类精密机械零件的塑性成形。

    As a part of less machining technology , warm-extruding has the advantage of higher forming accuracy and lower deformation force and it can also be used to continuous production . Gradually , it has been used in plastic deformation of many precise mechanical parts .

  30. FLAC在煤岩变形破裂力电耦合规律研究中的应用

    Application of FLAC in the research on the coupling laws between EME and stress fields during the deformation and fracture