sheetmetal

A Design of Computerized Testing and Control System for Sheetmetal Combined Testing Machine

钣金综合试验机计算机测控系统设计

3-D Surface Reconstruction of Irregular Industrial Sheetmetal Parts Based on Structure Illumination

基于结构光的不规则工业钣金件三维曲面重建

Deformation analysis of sheetmetal die in the process of punching

钣金件模具在冲压过程中的变形分析

Research and development of object-oriented sheetmetal CAM systems

面向对象的板金CAM系统的研究与开发

Press down new seal all around the sheetmetal flange .

将新密封件沿金属板法兰四周按紧。

Do not put it on the sheetmetal part !

不要将它放在钣金件上！

To do this , fit the sheetmetal ring and tighten using special key .

为此，安装钢片环并用专用钥匙拧紧。

Secure the line with a new sheetmetal clip .

用新的钢板夹固定控制管路。

Remove sheetmetal support for coolant pipes in the centre tunnel .

拆下中央通道中冷却液管的钢板支架。

Fit tension cable to the shaped sheetmetal part .

将张紧拉线安装到成型钣金件上。

To do so , fit the sheetmetal ring and tighten using the key .

为此，先安装钢片环并使用扳手将其拧紧。

Check sheetmetal nuts for deformation , replacing if necessary .

检查钣金螺母是否变形，必要时更换。

Lines Extraction of Industrial Sheetmetal Parts

一种高精度的工业钣金件图像直线提取算法

Move throttle housing into installation position and place sheetmetal reinforcement around the throttle housing .

将节气门壳移动到安装位置并将金属板加强件置于节气门壳周围。

Check sheetmetal nut and replace it if necessary .

检查钢板螺母，必要时予以更换。

The required sheetmetal clips listed in the table below must be used , depending on the vehicle equipment .

根据车辆设备不同，必须使用下表中列出的所需的金属板卡子。

Only apply body sealant to primed sheetmetal parts .

只能将车身密封胶涂抹在涂过底漆的钣金件上。

Remove all the old sealant from the sheetmetal flange .

从金属板法兰上清除所有旧的密封胶。

Tighten the seat rail cover with the sheetmetal screws .

用自攻螺钉拧紧座椅轨罩。

Fasten the front end with the sheetmetal screws .

使用钣金螺钉紧固前端。

Check both sheetmetal clipsand both fastening parts , replace if necessary .

检查两个钣金卡子及两个紧固件，必要时应进行更换。

Loosen sheetmetal reinforcement around the throttle housing .

松开节气门壳周围的金属板加强件。

Clip side cover into the sheetmetal clip of the a-pillar .

将侧盖卡入a柱的金属夹。

Guide the bulb into the sheetmetal holder at an angle and press it to the side .

以一定角度将灯泡导入钢板架，并将其压向一侧。

Ensure that sheetmetal clip is fitted correctly .

确保正确安装了金属板卡子。

Remove upper screw on sheetmetal holder .

拆下钢板架上部的螺钉。

Our products are extensively applied to communications , automotive , medical , aerospace , sheetmetal , electronical industry , etc.

产品广泛运用在电子通讯、汽车、铁路、钣金、机械器材和仪器、航天等领域。

Ensure that the sheetmetal clips engage correctly .

确保正确卡入金属卡子。

Fasten the front end with the sheetmetal screws and the spacer sleeves .

用自攻螺钉和间隔垫圈紧固前端。

Install diagonal braces and sheetmetal cross member .

拆下杆和薄壁横梁。