pinioned

At nine the next morning Bentley was pinioned , hooded and hanged .

次日上午9点，本特里被捆住双臂、戴上头罩，然后绞死了。

His arms were pinioned to his sides .

他的双臂被绑在身体两侧。

They were pinioned against the wall .

他们被牢牢地靠墙绑着。

Pinioned by the press of men around them , they were unable to move .

周围的人群挤压着他们，使他们动弹不得

Study on Geometric Model for Manufacturing of a New Type of Pinion Cutter

关于新型插齿刀工业实现的几何模型研究

Development and Application of CAD System for Pinion Cutter

插齿刀CAD系统的开发与应用

Determining Method of Major Parameters of Pinion Shape Cutter

插齿刀主要参数的确定方法

A Study on Rack and Pinion Steering Gear with Variable Ratio

变速比齿轮齿条式转向器的共轭分析

One on each side of the pinion shaft providing superior dynamic load capacity .

其中的每个小齿轮，提供卓越的动态负载能力轴一侧。

A study on cad / cam model of spiral pinion shaped cutter

关于螺旋插齿刀CAD/CAM几何模型研究

Assembly Method of Spiral Bevel Pinion in a New Type of Drive Axle

新型驱动桥主动螺旋伞齿轮的装配方法

Check ring gear and pinion gear teeth contact pattern .

检查环形齿轮齿接触印痕。

He is held with his arms pinion together behind his back .

他被捉住反剪著双臂。

This paper introduces a optimization method of pinion cutter for cutting helical gears .

介绍一种斜齿插齿刀的刃形优化方法。

Indirect valve gear End play in drive pinion bearings .

间接式气门驱动机构驱动小齿轮轴承的端隙。

System design of machine for measuring bevel drive pinion preloads based on industrial PC

基于工控机的汽车主锥预紧力测量机控制系统设计

Ways to improve the pinion life of a minor grinder

提高中小型磨机小齿轮使用寿命的途径

Application of AC frequency speed system controlled by PLC in rank and pinion ship elevator

PLC控制交流变频调速控制系统在船用电梯中的应用

Rear axle differential side gear differential spur drive pinion cross shaft

差速器传动（正）齿轮后桥差速器半轴齿轮

Effect of the Relief Angle of Pinion Cutter on the Gear Root Diameter

插齿刀的实际后角对齿轮根径的影响

The Study on EHL of Plastic Pinion Engaging with Steel Gear

塑料与钢制齿轮啮合的弹流润滑研究

Research on error compensation technique for regrinding of pinion cutter

插齿刀重磨误差补偿技术的研究

The Virtual Design and Analysis of UG based Rack and Pinion Redirector

基于UG的齿轮齿条式转向器的虚拟设计与分析

Determination of Meshing Parameter of Pinion Machine Tool in Cutting Bevel Gear Transmission

切制锥齿轮传动的小齿轮时机床啮合参数的确定

Drive pinion cone bearing cup inherit and carry forward one 's fine traditions

传动小齿轮锥形轴承杯继承和发扬优良传统

Usually , we adopt pinion drive for large mills .

大型磨机我们通常采用边缘驱动。

The Generation of Face - Gear Drive with Helical Pinion

基于斜齿小齿轮的面齿轮的齿面生成研究

Frequent changes of pinion in drawing and ring spinning .

并条与细纱工序（轻重）小齿轮更换频繁。

The design of drive shaft is rational in mill system of single - pinion drives .

边缘传动式磨机系统的传动轴的设计是合理的。

New configured hardened face gear pinion cutter and its CAD

新构形法硬齿面插齿刀及其CAD