notching

The economy is expanding , notching up high growth rates .

经济在发展，实现了高增长率。

Results are very linear and free from phase notching .

结果非常线性，没有相位凹口

This means that the system only improves , always notching forward , never backsliding .

这意味着系统只能够被改进，总是向前的，从不会倒退

The Design and Finite Element Analysis of Notching - Machine

压槽机的设计和有限元分析

Design of Level Swing Notching Dies for Support Rack

托架水平摆动切口冲模设计

The Modification of Material Clamping Device of a Notching Press

冲槽机压料装置的改进

The Improvement of the Construction for Saw Disc Locating Device of Stator Notching Press

定子冲槽机牙盘定位装置结构改进

Notching machine for working metal not numerically controlled

开槽机，用于金属加工，数字控制

Experimental research on notching wet beach of Yellow River by short-delay blasting

黄河湿滩微差爆破开槽试验研究

When notching two layers of fabric , notch each layer alternately .

两层面料都需打刀眼时，必须一层一层地交替进行。

Analysis of the Mechanism for Notched Borehole Blasting and the Parameter Design for the Notching Tool

刻槽爆破的机理分析及刻槽刀头参数设计

QNX Based Control System of Assistive Robot auxiliary notching device for metalworking machine tools

基于QNX实时系统的行为辅助机器人控制系统辅助天槽器，用于金属加工机床

Design of Progressive Die with Side Notching and Horizontal Blanking for Drawing Part tangential feed mechanism

侧冲缺口-横向冲切落料拉伸级进模切向进给[进刀]机构

Cutting , notching , or drilling a beam may seriously affect its ability to carry the design load .

切割、冲口加工或钻胶合木梁时可能会对其设计负荷能力产生严重影响。

A Kind of Combined-mechanical-interlocking Clutch and Brake Using in Notching Machine

用于冲槽机的组合式机械连锁离合器&制动器

Be careful when cutting , notching , or drilling .

切割、冲口加工和钻孔时要小心。

Reducing the Cogging Torque of PM Motor by Stator Teeth Notching

采用齿冠开槽法有效抑制永磁电机齿槽力矩

YAG solid laser notching is an technology , but the choice of laser processing parameter depends on experience mainly .

YAG固体激光切槽是当前最先进的连杆裂解槽加工工艺，但其激光加工参数的选择主要依靠经验。

A Probe into Fracturing Mechanism of Notching Blasting

切槽爆破断裂成缝机理的探讨

Design of the Notching Die for the Fusing Seat Clips and the Improvements

熔座夹切口成形模设计及改进

Turning before notching groove in the roll Improvement of Notching Die Structure for the Joint

硬质合金轧辊开槽前的车削加工工艺联接头冲槽模结构改进

Auxiliary notching device for metalworking machine tools

辅助天槽器，用于金属加工机床

Radio frequency noise jamming can be deleted by the method of average range frequency spectrum and notching in frequency domain .

对于射频噪声，通过平均距离频频法和频域陷波的方法可以去掉；

The design characteristics and the manufacturing technology of the notching block of the die for the shutter sheets were introduced .

以弯管件为例，介绍了杠杆式切口模的结构及工作过程，并详细介绍了左、右导向板的设计方法及其设计时应注意的问题。

Study on notching angle in notching blast

切槽爆破中切槽角的研究

The application of the notching die increased work efficiency , lowered labor intensity , and met the demand of batch production .

切口模的应用提高了工效，降低了劳动强度，满足了批量生产的要求。

Responsible for all production processes including cutting , notching , coating , moulding , trimming , packaging , etc.

负责所有的生产工艺过程，包括切割、冲缺、喷涂、接角、修边及包装等等。

An improved notching method with derivation of power spectrum and mean denoising was presented to realize a sensing system with good frequency response property .

提出了一种利用功率谱一阶求导和均值去噪的改进型陷波方法，实现了具有良好频响特性的传感系统。

Based on fracture mechanics for rock and practice in marble culling , the technique of notching blast is presented here .

切槽爆破技术是作者在岩石断裂力学理论和大理石矿实际开采要求的基础上提出的。

Combination blooming billet mil Improvement of Notching Position for Side Notching in Pickling-Tandem Cold Mill Line

初轧-轧坯联合轧机酸洗-冷轧机组中侧冲剪冲切位置的改进