Compound die

Design of the Automatic Compound Die for the Computer Case

电脑机箱自动复合模设计

Design of Drawing and Extruding Compound Die for Step Parts

阶梯件拉伸挤压复合模设计

The compound die structure and working principle were introduced .

介绍了落料-拉延-翻边复合模的模具结构及其工作原理。

Processing Method of Compound Die with Hard Alloy for Silicon Steel Piece

硅钢片硬质合金复合冲模工作零件加工方法

Research on heat treatment process of 65 Nb steel compound die for manufacturing

采用65Nb钢的C（63）侧架磨耗板复合冲模热处理工艺研究

Design and Manufacture of the Shared Plate for the Compound Die

复合模共用模板的设计与加工

Design of the Compound Die with Two - stage Floating Elastic Pressing

二级浮动弹压复合模设计

Technological Analysis and Design of Compound Die for Diesel Engine Machine Oil Scale Frame

柴油机机油标尺座冲压工艺分析与复合模设计

The structure design of compound die of six procedures is introduced in detail .

对6个工序的复合冲裁模具在结构设计方面作了比较详细的介绍。

Development and ve search for compound die forging of gear

齿轮复合模锻的开发与研制

The designing application of compound die of external friction pieces

外摩擦片复合冲模的设计应用

Design of the Compound Die for Small Bent Parts

小型弯曲件复合模设计

Compound Die Casting Technique for Vacuum Pump Body

真空泵泵体外壳复合金属型铸造工艺

Design of Piercing and Blending Compound Die for the Blade Box

刀片盒冲孔弯曲复合模设计

Design of Forming Piercing Compound Die and Improvement for the Leaking Plate

漏盘成形冲孔复合模设计及改进

Design of Drawing and Piercing Compound Die with Floating Punch Block

带有浮动凸凹模的拉伸冲孔复合模设计

New Type Compound Die for Blanking and Drawing with Constant Blank Holder Pressure

新型恒压边力落料拉伸复合模

The design describes the structure of compound die stamping flip-chip design and working process .

本次设计阐述了冲压倒装复合模的结构设计以及工作过程。

Compound die design for signal receiver

电子信号接收器复合模具设计

Design of compound die of fine stamping eccentric brake ring

偏心制动圈精冲复合模设计

The CAD Design of Compound Die for Blanking and Drawing Based on SolidWorks

基于SolidWorks的落料拉深复合模CAD设计

The Compound Die Design

复合冲裁模设计

Design of Compound Die for the Muffler Plate

消声器后盖复合模设计

A Compound Die for Multiple Parts with No Scraps

一模多件无废料复合模

Design of Baffle Compound Die Complex Numbers

隔板复合模设计

In addition , both the working process of compound die and questions required attention are stated .

同时也阐述了复合模工作过程及注意事项。

Design of Drawing and Piercing Compound Die

拉伸冲孔复合模设计

The Flexible Compound Die for Stamping and Forming The Design for Stamping Die of Composite Structure

柔性冲压成形复合模镶拼式冲模设计

The Flexible Compound Die for Stamping and Forming

柔性冲压成形复合模复动轮拉杆式抽油机

Elastic Unloading Settings Preventing Working Parts From Inserting Waster in Compound Die

复合模中防止工件嵌入废料的弹性卸料装置