变形力
- 网络deformational force;deformation force;strain force
-
三层复合板轧制复合变形力的计算
Calculation of rolling deformation force of three-ply cladding sheet
-
改善模具的润滑条件,可大幅度地降低变形力。
The improvement of lubrication condition of die can considerably decrease the deformation force .
-
根据变形力的强度,褶皱可以是平缓的,陡峭的,倒转的,或逆掩的。
Depending on the intensity of the deforming forces the folds may be gentle , sharp , overturned , or overthrust .
-
热挤压变形力的粘塑性模式解
Solution of deformation force in hot extrusion with viscoplasticity model
-
锥形件柔性旋压成形时的变形力分析
Analysis of the Spinning Forces on Flexible Spinning of Cones
-
用工程法求解可膨胀管塑性变形力
Calculating plastic deformation force of expandable tubules by engineering method
-
电机换向器整体冷锻变形力的计算
Forming pressure calculating of integral motor commutator cold forging
-
挤压工艺轴对称状态与平面应变状态变形力之间的关系
Deforming Force Relationship Between Axisymmetric State and Plane Strain State in Extrusion Technology
-
等径弯曲通道变形力的研究
Calculation of extrusion force in equal channel angular pressing
-
利用塑性介质挤胀成形三通管接头变形力的研究
Research on the Deformation Force of Extrude-bulge Forming of Tee Junction Using Plastic Medium
-
开式模锻型腔充满阶段和锻靠阶段的变形力
The deformation force in cavity of closed-die in stages of filling and die kissing
-
超塑性材料的镦粗变形力的研究
Upsetting forming pressure study of superplastic materials
-
用能量法研究超塑性矩形条料镦粗的变形力
Calculation of deformation force for superplastic rectangular blank ( plane strain ) upset by energy equilibrium
-
实体可膨胀管变形力与膨胀工具模角关系研究
On the relationship between the deformation force of solid expandable tubular and model angle of expandable tool
-
变形力沿宽度方向的分布都是关于b/h函数。
Distortion force distributing along the direction of breadth is a kind of function about b / h.
-
采用矩阵算子法计算已知滑移线场理论变形力
Calculation of the Theoretical Working Pressure of a Given Slip Line Field by Using the Matrix Operator Method
-
应变速率、液体体积分数和液体粘度对金属半固态成形变形力的影响
Effects of strain rate , liquid volume fraction and liquid viscosity on deformation force of semi-solid compression of metals
-
本文应用逐次单元法推导了开式冲孔变形力计算公式。
In this paper the deformation load formula of open die punching were derives by the successive element method .
-
冷挤压制造圆柱体形孔内侧表面的矩形螺旋单元时的变形力计算
Calculation of the deformation force during manufacture by cold extrusion of square screw elements on the internal surface of cylindrical cavity
-
分析影响旋压工艺变形力的主要因素,介绍了确定旋压工艺力的基本方法。
Through analysing the main factor that affects spinning technology deform force , this passage introduces the basic method of spinning technology force .
-
弹性可被定义为当施加于材料上的变形力被撤除时,材料恢复其原来形状的能力。
Elasticity can be defined as the ability of the material to return to its original shape when the deforming force is removed .
-
应用古典振动理论及冲击波动理论,对三种弹性元件悬架车辆的振动进行模拟并对响应进行分析。提出用冲击波动力学分析车辆振动的理论依据,由此建立车辆的波阻力及变形力振动模型。
The classical vibration theory and impact wave theory are applied to simulate the helical spring suspension vehicle vibration and its response is analyzed .
-
根据破裂模型和拉深变形力,导出了破裂极限预报与控制判据。
On the basis of the fracture model and the deep drawing deformation force . The fracture limit prediction and control criterion is calculated .
-
从谐波齿轮传动的原理和特点出发,分析短筒谐波齿轮传动中短筒柔轮的变形力和应力急剧增加的问题。
Based on the principle and characteristic of harmonic gear driving , researched the problem about the sharp increase of stress in short flexspline deformation .
-
阐述用机械压力机进行粉末热锻时Fe-0.22C粉末烧结体热复压变形力的工程计算。
This paper expounded the engineering calculation of deformation force for the hot repressing of the Fe 0.22C powder sintered preforms in the hot powder forging by mechanical press .
-
对影响16MnCrs钢温锻成形工艺的主要因素锻造温度、表面氧化、摩擦、润滑和变形力进行了研究,并给出了大量的实验数据。
Some research work have been done in the key influence factors on warm precision forging process , i. e. , temperature , oxidation , friction , lubrication and deformation forces .
-
上限模拟通过所设计的简便精确的动可容速度场,获得了变形力和轴对称变形区的变化规律。
Through an easy to use and accurate enough kinematically permissible velocity field designed with UBM , the magnitude of deformation force and the regularities of axisymmetrical deformation zone are obtained .
-
基于滑移线场的简化流动模型,运用数学方法求解出了一种锥形模正挤压变形力的最佳上限解,并将该上限解用通用解析式表达出来。
The deforming force of cone-die direct extrusion is solved by a mathematic method based on the simplified flow model of slip line field . The optimum upper bound solution is also represented in analytic mode .
-
温挤压作为一种少无切削成形技术,因其成形精度高、变形力小,且可连续生产的特点,已被逐渐用于各类精密机械零件的塑性成形。
As a part of less machining technology , warm-extruding has the advantage of higher forming accuracy and lower deformation force and it can also be used to continuous production . Gradually , it has been used in plastic deformation of many precise mechanical parts .
-
FLAC在煤岩变形破裂力电耦合规律研究中的应用
Application of FLAC in the research on the coupling laws between EME and stress fields during the deformation and fracture