首页 / 词典 / good

vios

  • 网络威驰
viosvios
  1. I find the VIOS command line much faster and easier .

    我发现VIOS命令行快得多,也更容易。

  2. Verify the virtual device configuration and status on each VIOS .

    检验每个VIOS上的虚拟设备配置和状态。

  3. For a Power environment , the image repository must run in a VIOS .

    对于Power环境,映像存储库必须在一个VIOS中运行。

  4. These steps were to check the general health of the VIOS .

    这些步骤检查VIOS的健康状态。

  5. Run this command on the source VIOS during the migration .

    在转移期间,在源VIOS上运行此命令。

  6. On VIOS , we need to create four virtual Ethernet ports .

    在VIOS上,我们需要创建4个虚拟以太网端口。

  7. Make sure VIOS has sufficient CPU , memory , and network bandwidth .

    保证VIOS具有足够的CPU、内存和网络带宽。

  8. Document the current virtual device mappings on each VIOS .

    记录每个VIOS上当前的虚拟设备映射。

  9. From the storage area network ( SAN ) and assigned to VIOS .

    来自存储区域网络(SAN),分配给VIOS。

  10. Discover , request access , and collect inventory on the VIOS

    发现、请求访问和收集VIOS上的清单

  11. On the secondary VIOS , verify whether the Ethernet state is BACKUP .

    在辅助VIOS上,验证以太网状态是否为BACKUP。

  12. Nodes : System p servers can be standalone partitions or vios clients

    节点:Systemp服务器可以是单独的分区或VIOS客户机

  13. Repeat the same verification procedures for the second VIOS .

    对另一个VIOS重复相同的检查过程。

  14. The sections that follow explain how to configure the VIOS .

    以下各节解释如何配置VIOS。

  15. Perform a health check on each VIOS .

    对每个VIOS执行健康状态检查。

  16. The VIOS partition profile is also updated to reflect the removal of these virtual devices .

    VIOS分区概要文件也进行了更新以便反映这些虚拟设备的删除。

  17. Before starting my LPARs , I first performed several health checks on each VIOS .

    在启动LPAR之前,先在每个VIOS上执行几个健康状态检查。

  18. I noticed that the boot list on each VIOS had changed .

    我注意到,每个VIOS上的引导列表改变了。

  19. I activated one of the VIOS and waited while it started to boot .

    我启动一个VIOS,等待它开始引导。

  20. Start functional verification of the environment , such as VIOS failover and application startup and test .

    开始对环境进行功能性检验,比如VIOS故障转移以及应用程序启动和测试。

  21. The physical disks must be assigned to both paging VIOS partitions .

    这些物理磁盘必须分配给两个分页VIOS分区。

  22. Paging will normally be provided by the primary paging VIOS partition .

    正常情况下,由主分页VIOS分区提供分页功能。

  23. Verify that the same SAN disk can be seen by both VIOS .

    确认两个VIOS都可以看到同一个SAN磁盘。

  24. To check the primary Ethernet adapter from both VIOS , we can use the following command .

    要检查来自两个VIOS的主要以太网适配器,可使用以下命令。

  25. The VIOS itself can be installed on either the internal disk or SAN disk .

    VIOS本身可以安装在内部磁盘或SAN磁盘上。

  26. Mobility activity is logged on the LPAR and the source and target VIOS .

    转移活动被记录在LPAR以及源和目标VIOS上的日志中。

  27. All physical devices were owned by the Virtual I / O servers ( VIOS ) .

    所有物理设备都属于VirtualI/O服务器(VIOS)。

  28. However , after an initial spurt , sales of the Vios have been weak .

    然而,在经历最初的井喷之后,威驰的销售一直较为疲软。

  29. For this we need the number of the LPAR to identify VIOS disks mapping .

    为此,我们需要LPAR的编号来识别VIOS磁盘映射。

  30. This is to allow the target VIOS the ability to " take over " the storage during a migration .

    这使目标VIOS能够在转移期间“接管”存储。