首页 / 词典 / good

t6

t6t6
  1. Influence of Solution Treatment T6 on Mass Effect of Cylindrical Aluminum Alloy Casting

    T6固溶处理对圆柱形铝合金铸件尺寸效应的影响

  2. The study has some good meaning for optimizing the technology of T6 and double aging .

    该研究对进一步优化A356合金轮毂T6处理工艺和双级时效工艺具有一定的意义。

  3. T6 treatment also increased the mechanical properties , especially the sub-yield properties .

    随后的T6处理进一步提升了复合材料的力学性能,特别是小变形抗力。

  4. The products stiffiness all are acceptable using T6 solution heat treatment .

    采取T6固溶的热处理工艺,经验证其铸造产品硬度均达到合格标准。

  5. Effects of relevant processing parameters of T6 treatment on mechanical performance of alloy are investigated with orthogonal experiments .

    通过正交试验分析了T6处理的有关工艺参数对合金力学性能的影响。

  6. Optimize Research on T6 Heat-treatment of Aluminum Cast Wheel

    铸造铝合金轮毂T6热处理工艺的优化研究

  7. Both of the alloys were T6 tempered to peak status .

    合金均经T6时效处理,达到峰值时效状态。

  8. 2219 - T6 aluminum alloy was welded using FSW .

    对2219-T6铝合金进行了直接搅拌摩擦焊接。

  9. And the semi-solid die casting after heat treatment by T6 , mechanical properties have further improved .

    而半固态压铸件经T6热处理之后,力学性能有进一步的提高。

  10. Trichoderma sp . T6 xylanase production condition in solid state fermentation and the enzyme properties

    木霉菌株T6木聚糖酶固态发酵条件和酶学性质研究

  11. The T6 heat treatment after HIP would lead to serious deformation and cleavage of the blades ;

    HIP后进行T6处理,将导致叶片严重的变形和开裂;

  12. Influence of T6 treatment on microstructure and compressive property of SiC / Al double-interpenetrating composites

    T6热处理对复式连通双连续相SiC/Al复合材料性能的影响

  13. But the addition of Sc can make the strength of 2195 alloy decrease in T6 temper of higher temperature .

    但添加微量Sc却使2195合金在较高温度时效的T6工艺条件下表现出强度和塑性都有较大幅度的下降。

  14. Results The population doubling time of HSC T6 was 10.57 hours and its cloning efficiency was 82.4 % .

    结果HSC-T6细胞成活率较高,细胞在指数增殖期的细胞群体倍增时间为10.57h,克隆形成率为82.4%。

  15. The anti proliferation effects of the drugs on HSC T6 cell were evaluated by MTT assay .

    应用MTT比色法测定HSC-T6细胞增殖及评价药物对细胞增殖的作用。

  16. The levels of CK-MB at T6 in group B were lower than those in group C ( P0.05 ) .

    B组在T6时CK-MB水平较C组低(P0.05)。

  17. Followed by T6 treatment .

    其次是T6处理。

  18. After skin closure ( T6 ) . Applied Anatomy of Posterior and Lateral Femoral Cutaneous Nerve Graft

    股后及股外侧皮神经移植的应用解剖

  19. The mechanical properties of the alloy in T5 condition are higher than those in T4 and T6 conditions .

    在该温度二次挤压的合金T5态的力学性能明显高于T4和T6状态。

  20. Methods HSC T6 were cultured in different concentrations of curcumin and amiloride for 24 hours .

    方法HSCT6细胞与不同浓度的姜黄素、阿米洛利共同培养24h。

  21. The left atria CO was significantly higher than that in the right atria except T6 ( P < 0.05 );

    除T6时点,左房血CO含量均明显高于同时点右房血(P<0.05);

  22. The findings of the research have shown that the separating - out - phases from T6 matrix are composed of G.

    研究结果表明,T6状态基体析出相由G。

  23. The fracture mode of the alloy in T6 state is transgranular shearing and intergranular dimple mixed fracture .

    合金T6态的断裂方式为穿晶剪切和沿晶韧窝混合型断裂;

  24. After the post-weld T6 heat treatment , the tensile strength of the joints is equal to the BM .

    焊后经T6热处理,可与同炉热处理母材等强。

  25. After strengthening solution and T6 treatment , the tensile strength and elongation of studied alloy are 829.4 MPa and 5.7 % , respectively .

    合金经强化固溶和T6处理后,抗拉强度σb达829.4MPa,伸长率δ为5.7%;

  26. However , the third-order sequence boundary properties of T2 , T4 , and T6 are apparently different among different sub-sags .

    然而,T2(沙一段底)、T4(沙三段上亚段底)和T6(沙三段中亚段底)三级层序界面的性质在不同凹陷问具有明显的差异性。

  27. Objective : T6 study the efficacy of mosquito-repellent incense in lab and application in field test , the affection of application duration to protection effect .

    目的:研究蚊香实验室药效与现场实际应用效果及蚊香使用时间长短对防护效果的影响,并分析现行蚊香药效试验及评价标准的适用性;

  28. Noting from the physiological view , T6 and T7 treatments were the optimal combination for strawberry growing . 5 .

    说明从生理指标看,T6和T7处理是草莓生长的最优组合。

  29. Changes of microstructure and performance of the eutectic aluminum-silicon casting alloy processed by different modifications during heat treatment process ( T6 treatment ) are studied .

    研究了经不同变质处理后的共晶铝硅铸造合金在热处理(T6处理)过程中组织与性能的变化。

  30. After hard anodizing , surface roughness increases , the surface roughness of artificial aging ( T6 ) is bigger and grows faster .

    硬质阳极氧化后表面粗糙度都增加,且经T6处理后的表面粗糙度更大、增长更快;