peak-to-peak value

A method of computing peak-to-peak value of data dependent jitter

一种计算数据相关性抖动峰峰值的方法

Analysis of peak-to-peak value of data dependent jitter in high speed serial interconnect system

高速串行互连系统数据相关性抖动峰峰值分析

Direct peak-to-peak value correlation has high precision , but its computation is complex relatively and takes more time .

直接幅值相关计算方法精度高，但是计算复杂度较高，计算时间相对较长。

Then 6 parameters including peak-to-peak value and absolute average value were selected as diagnostic parameters and diagnostic model was built .

选取峰峰值、平均振值等6个参数作为诊断特征参数，建立了诊断模型。

Peak-to-peak value holding circuit of AES

俄歇能谱仪用峰峰值保持电路

The maximum peak-to-peak value of the timing variations in synchronous data expressed as a percentage of the ideal bit period .

在以理想的位周期的百分数表示的同步数据里，用以表示两个峰值间的最大定时变化值。

The accuracy of dynamic measurement of the interval between diameters of circular grating is 0.16 second of are ( peak-to-peak value ) .

动态检测圆光栅直径间隔的准确度为0.16〃（峰-峰值）。

And from this analytic the influence of set magnetism link hysteresis characteristics to the OCT peak-to-peak value , profile , frequency , non-periodic component survey .

并由此分析集磁环磁滞特性对OCT幅值、波形、频率、非周期分量测量的影响。

The voltage peak-to-peak value is 10.24V with amplitude resolution 0.01V . The phase range is 1 to 360 with phase resolution 1 .

输出电压峰峰值为10.24V，调幅步进为0.01V；初相调节范围为1°～360°，初相调节步进为1°。

Its cycle is less than or equal to 2 π, decided by the number of work cylinder . And the peak-to-peak value is also decided by n and Vk_0 .

压力和流量特性除有波动性外，还具有脉动性，其周期≤2π，由工作缸数决定，幅值大小也取决于n和Vk0。

Methods to rotor of centrifugal compressor 's condition monitoring and fault diagnosis are summed up . Peak-to-peak value is an essential reference value of centrifugal compressor 's condition monitoring , which is easy to implementation in practice .

总结了离心式压缩机转子振动的监测和诊断的方法：在压缩机的状态监测的方面，峰&峰值是其主要的手段，实践证明其实现过程非常简单而且非常有效；

Then from the focus error signal the traverse focus offset is calculated by the focus error occurring time , and the traverse focus error sensitivity and linear range are calculated by the focus error slope and peak-to-peak value .

然后根据聚焦误差曲线计算出小机芯离焦检测系统的特性，利用聚焦误差曲线S状脉冲的出现时刻计算出离焦偏置，利用S状脉冲的斜率和峰峰值得到离焦灵敏度和线性区范围；

As to the traditional direct torque control method , we make a introduction of its basic principle , make a fully description of the inverter switching states which affect the flux peak-to-peak value of the stator and to the electromagnetism torque .

对于传统直接转矩控制方式，我们介绍了其基本控制原理，详细分析了逆变器各开关状态对异步电动机定子磁链幅值和电磁转矩的影响。

The maneuver flight will depress the nonlinear response ; however the position of axis center will be obviously deflected . It will also lead to nonlinear response or peak-to-peak value jump near the fraction frequency of swing critical speed .

水平盘旋和俯冲拉起对深度非线性响应的抑制作用不是很明显；并且，水平盘旋和俯冲拉起会激起转角临界转速分频附近出现非线性振动或峰-峰值较大幅度的跳跃。

The function of LCD-driving part is outputing certain frequency according to the commands received by the serial line , peak-to-peak value , drive way and bias value of the waveform drive LCD display , and LCD driver uses the dynamic and bias-driving method .

包括液晶驱动和数据接收两部分，液晶驱动部分的功能是根据串口接收的命令输出一定频率，峰峰值，驱动路数和偏压值的驱动波形驱动液晶显示，液晶驱动采用的是动态偏压驱动法。

The important failure characteristic of the reciprocation type machinery is that the machine are always accompanied with the unusual vibration and the noise . Its vibration signal from the peak-to-peak value territory , the frequency domain and the time domain real-time has reflected the mechanical failure information .

往复式机械发生故障的重要特征是机器伴有异常的振动和噪声，其振动信号从幅值域、频率域和时间域实时地反映了机器故障信息。

The wave output employs two D / A converters ( DAC0832 ) one of which controls the voltage reference of the other converter in order that the peak-to-peak value of the end output wave varies from 0 to 5 volts stepped according 1 volt .

输出采用双D/A技术，用一片DAC0832控制另一片DAC0832的基准电压，从而使输出波形峰-峰值在0~5V之间能够按1V步进。