melt viscosity

Effects of melt viscosity on the preferential intercalation behavior of clay in immiscible polypropylene / polystyrene blends

熔体黏度对黏土在聚丙烯/聚苯乙烯共混物中优先插层行为的影响

The melt viscosity is improved by adding calcium in Al-Si alloy powder so as to control the surface tension of the melt .

采用在铝硅合金粉末中加钙来增加熔体黏度，控制熔体的表面张力；

The Effect of Vibration field on the Polymer Melt Viscosity

振动力场对聚合物熔体黏性的影响

Study on melt viscosity of alloy in surface metallurgy by plasma beam

等离子表面冶金熔体粘度的研究

The construction and function of high temperature melt viscosity test instrument are introduced in this paper .

介绍了高温熔体粘度测试仪的组成和功能。

A New Method for Measuring High-Temperature Melt Viscosity

测量高温熔体粘度的一种新方法

The processing technics had effects on melt viscosity .

加工工艺对熔体的粘度也有影响。

Study on the influence of melt viscosity on co-injection molding

熔体粘度对共注成型影响机理的研究

The melt viscosity and die swell ratio decrease when the chips contain water .

水分存在会导致熔体粘度下降，胀大比减小。

Study on Melt Viscosity of Foam Plastics

泡沫塑料熔体粘度的研究

Effect of melt viscosity on phase transition in PP / EHDPET blends

PP/EHDPET共混体系熔体粘度对相转变的影响

A study on MWD of PP by zero shear rate melt viscosity and the melt index

用熔体的零切粘度和熔融指数研究聚丙烯的分子量分布

The effect of various materials on soften point and melt viscosity of hot melt adhesive were discussed .

讨论了各种基料对热熔胶软化点、熔融粘度的影响。

Study on Melt Viscosity of PP and FEP / PP Blends at Low Shear Rates

PP及FEP/PP低剪切速率下熔体粘性研究

The reliability of the apparent melt viscosity on the temperature was reduced while the shearing rate was higher .

高剪切速率时，表观粘度对温度的依赖性降低。

A thermoplastic polyester elastomer designed for blow molding or processing techniques requiring high melt viscosity .

热塑性聚酯弹性体设计用于吹塑或处理技术要求高熔体粘度。

The cross-linking decreased the degree of crystallinity and the temperature sensibility of melt viscosity .

由流变曲线看出，交联降低了PP熔融黏度对温度的敏感性；

Design and optimization of control program of melt viscosity in double drive disk reactor for PET direct spun filament

直纺长丝双驱动圆盘反应器熔体粘度控制程序的设计和优化

Incorporation of nano TiO 2 lowered the melt viscosity of PET .

纳米TiO2的加入明显降低了PET的熔体粘度。

We also discussed how spinning temperature influenced spinning compact , melt viscosity , spinnability , breaking strength .

探讨了纺丝温度对纺丝组件、熔体粘度、可纺性，断裂强度的影响。

Real-time Measurement and Research of Apparent Melt Viscosity during Pulsating-Pressure Induced Plasticating Injection Molding

动态充模过程熔体表观黏度的实时测量与研究

The blend melt viscosity was decreased with increasing ABS content when ABS content was 0 ~ 50 % ;

当ABS含量为0～50%时，共混体系的表观粘度随ABS的含量的增加而降低；

The electric current and alloy elements in powder system are major factors for influencing melt viscosity in surface metallurgy by plasma beam .

影响等离子表面冶金熔池中合金熔体粘度的主要因素是电流和粉末体系中的合金元素。

The head pressure increases when the melt viscosity and temperature decreases , so the products will have good shape and favorable stability .

温度降低时，熔体黏度大，机头压力增加，挤出制品压的较密实，形状稳定性好。

PVC foam melts and the following factors : baking temperatures , baking time and PVC melt viscosity .

PVC熔体发泡和以下因素有关：烘烤温度、烘烤时间和PVC熔体粘度。

DINP-S exhibits lower melt viscosity than DOP under typical conditions of PVC extrusion processes .

在典型的挤出加工条件下，DINPS比DOP更能降低混合料的熔融粘度。

This is because water degraded PLA which caused melt viscosity and intensity reduced , and cell broken when foaming .

这是因为在加工过程中水引起聚乳酸的部分降解使得熔体粘度和强度降低，发泡时泡孔易破裂。

The melt viscosity of the cyclic oligomer is very low which is necessary to impregnate the carbon reinforcement well .

研究发现环状聚芳醚酮齐聚物熔融温度低，熔体粘度小，具有良好的流动性，十分有利于充模成型及浸渍增强纤维。

The results showed that the melt viscosity and decomposition of TiH_2 are the two predominant factors on which the bubble stability depends .

确定熔体的黏度与氢化钛分解是决定气泡稳定的主要因素。

In addition , the melt viscosity and processing power of PVC-TPE could be effectively reduced with adding of the acrylate monomer .

此外，丙烯酸酯单体的加入能有效地降低PVC熔体的粘度，使加工能耗降低，添加的丙烯酸酯橡胶的Tg越低，PVC-TPE的硬度、拉伸强度、撕裂强度越小。