Wear rate

Current has obviously affected on wear rate compared with loading .

在试验范围内，电流比载荷对磨损率的影响显著。

With load increased , friction coefficient decreases , wear rate increases .

SiC随载荷增加摩擦系数减少，但磨损率随载荷增加而增加。

Tests of Materials Wear Rate Used in Simulation Model for Wear Study

磨损数值仿真模型中材料磨损率试验研究

With the increase of temperature , the wear rate increased .

200℃以后摩擦因数迅速增大，且涂层的磨损率随着环境温度的升高而增大；

The relation between wear rate and fractal dimension were established and analyzed .

建立并分析了它们的表面分形维数与磨损率的对应关系，认为改善润滑条件和控制对摩偶件表面形貌是降低弹性金属塑料复合材料与钢对摩时磨损率的主要途径；

Relationship between filler 's size distribution and wear rate of composite resins

复合树脂的填料尺寸分布与磨损率的相关性

The wear rate of the alloy is increased with the increase of electric current .

在载流条件下，合金的磨损量随加载电流的增加而增大；

Wear rate showing an increasing trend with increasing sliding speed and contact current .

磨耗率随着滑动速度和接触电流的增大呈现增大的趋势。

The corrosion wear rate was higher than uniform corrosion rate at the same conditions .

相同条件下，腐蚀磨损速率大于均匀腐蚀速率。

The results are as follows : The wear rate increases with carbon content decreasing .

结果表明，钢的磨损率随炭含量的增加而降低，特别是经800℃时效处理，其降低倾向更大。

Composite coatings can reduce the friction coefficient and wear rate concurrently .

复合镀层同时兼有降低摩擦系数和降低磨损率的作用。

Numerical Simulation of Plastic Deformation Wear Rate of Materials under Three-Body Abrasion

三体磨损中材料塑性变形磨损的数值模拟

The mean linear wear rate was ( 0.125 ± 0.074 ) mm / year .

聚乙烯内衬平均线性磨损率为（0.125±0.074）mm/年。

While giving other parameters , wear rate increases along with the increase of contact area .

当其余各影响参数保持一定值时，磨损率随接触面积的增大而增大。

Because of short follow-up time the wear rate of the prosthesis need more further research .

但因本组病例随访时间较短，关于生物型假体的磨损率需要进一步观察。

When iron contents was among 12 % ~ 20 % wear rate changed slightly .

当铁含量在12%～20%之间时，磨损率随镀层中铁含量的增加变化不大。

The maximum specific wear rate is obtained at the contact pressure of 0.4 MPa .

载荷为0.4MPa时，比磨损率最大。

The law of wear rate with particles concentration and size variation was studied through the experimental method .

通过室内实验的方法研究了磨损率随粒子含量以及粒径的变化规律。

The calcium sulfonate additive reduces the wear rate of the materials .

基础油中磺酸钙的加入使氮化硅的磨损速率得到降低。

The results show that the weight loss and wear rate of composite are low compared with traditional material .

结果表明：与传统材料相比，在干摩擦磨损条件下复合材料的磨损量以及磨损率要低于其它材料。

With an increase in normal load , the specific wear rate of SiC disk increased .

随着法向载荷的增加，摩擦副材料的磨损率增大。

The upper layer has a higher surface hardness and lower wear rate than the lower layer .

上涂层较致密，表面硬度较高，磨损率较小，而下涂层较疏松，硬度较低，磨损率较大；

The wear rate and friction coefficient of the composite decreased with the increase of loading ;

随载荷增加，材料的磨损率及摩擦系数都不断减小；

The bigger the impacting velocity , the greater the erosion wear rate .

速度越大，冲蚀磨损率越大。

The wear rate of the pure carbon strip has the same varying tendency .

纯碳滑板的磨损率也呈现出相同的变化规律。

The specific wear rate is strongly dependent on the temperature , atmosphere and contact pressure .

比磨损率也与温度、气氛和接触压力密切相关。

It can be applied in neural network measurement for the instantaneous wear rate of cutting tools .

可作为刀具瞬时磨损率神经网络测量的端系统。

Research of the Wear Rate Calculation Method of Piston Ring & Cylinder Liner of Internal Combustion Engine

内燃机活塞环&缸套三体磨粒磨损设计计算方法的研究

Influence of Prepared Conditions on the Wear Rate of the Green Milling Media Prepared by Refractory Waste

工艺条件对用耐火材料废料制备的绿色研磨介质耐磨性的影响

The wear rate formula of UHMWPE pin in different friction directions is deduced .

推导了UHMWPE销变向摩擦下的磨损率公式。